GCSE · Physics · AQA · Spec 8463

Conservation and dissipation of energy

Your phone warms up while it charges. That warmth is energy that hasn't vanished — so where has it gone?

Useful or wasted?

Same energy, different verdict

Pick a transfer, then choose where its energy ends up. Then switch device and sort the same transfers again.

You want hot air blowing onto wet hair. Which transfers do that job?

Still to sort

Useful (0)

The energy ends up where you wanted it.

Dissipated (wasted) (0)

The energy spreads into the surroundings and is stored in less useful ways.

Where the line is: Wasted doesn't mean gone. The energy still exists — it's just spread out where you can't easily use it.

Destroyed — gone for good (0)

Energy that simply stops existing.

4 of 4 still to sort.

Look at 'The air gets warmer'. Useful in the hairdryer, wasted in the fan. The physics didn't change at all — only what you wanted.

Predict, then check

A closed system is one where no energy can get in or out. Picture a sealed box drawn round everything involved.

A pendulum swings inside a sealed box, so no energy can get in or out. A few minutes later it has stopped. What has happened to the TOTAL energy inside the box?

Work it out

An electric motor lifting a load is supplied with 500 J, but only 150 J ends up usefully raising the load. How efficient is it? Efficiency is simply the fraction that ended up where we wanted it: useful output energy transfer ÷ total input energy transfer. The same division works with power too: useful power output ÷ total power input. Once you've seen the answer, try swapping the two numbers and watch what happens.

Finding efficiency (ratio)

efficiency = useful ÷ total

Answer

efficiency = 150 ÷ 500

= 0.3 · 30%

Cutting the waste

How do we stop energy spreading where we don't want it?

Draw the arrows: which change leads to which effect? Then compare your web with the lesson's.

  1. Lubricate moving parts
  2. Add thermal insulation
  3. Make the walls thicker
  4. Build walls from a lower thermal conductivity material
  5. Slower energy transfer by conduction through the walls: the building cools more slowly
  6. Less energy dissipated by unwanted transfers
  7. Higher only: higher efficiency of the intended transfer (outcome)
Add a link

No links yet.

Now you write it

Testing thermal insulators

A student wraps beakers of hot water in different materials to find out which is the best thermal insulator, and whether a thicker layer of the same material works better. Describe how they should carry out the investigation and use their results. Then explain how the idea links to the walls of a building. [5 marks]

0 words · your answer stays on this page and is not sent anywhere.

WHAT YOU'VE LEARNED

A quick recap of today's lesson.

Energy is never used up — it just ends up somewhere less useful.

What you need to know

  • Energy can be transferred usefully, stored or dissipated — but it can never be created or destroyed.
  • In a closed system, energy moves between stores but there is no net change to the total energy.
  • In every system change, some energy is dissipated: it spreads out and is stored in less useful ways. This energy is often described as 'wasted'.
  • efficiency = useful output energy transfer ÷ total input energy transfer, and efficiency = useful power output ÷ total power input.
  • Lubrication and thermal insulation reduce unwanted energy transfers. Thicker walls, and walls with a lower thermal conductivity, make a building cool more slowly.

The big picture

Energy is never created or destroyed: it can be transferred usefully, stored, or dissipated. In a closed system the energy moves around, but the total never changes. Energy that is dissipated spreads into the surroundings and is stored in less useful ways — that's what we mean by 'wasted'. Efficiency tells you what fraction of the input ends up useful, and cutting unwanted transfers — with lubrication or thermal insulation, for example — means less energy is dissipated.

Key points

1Energy is never used up. It ends up either useful or dissipated.
2Closed system: energy moves around, the total stays the same.
3'Wasted' means stored in a less useful way — not destroyed.
4Whether a transfer counts as useful depends on what the device is for.
5Efficiency is useful ÷ total, so it can never be more than 1 (100%).
6Higher thermal conductivity means a higher rate of energy transfer by conduction.
7Higher only: to increase efficiency, reduce the unwanted transfers.

Worked example

Problem

A filament lamp has a total power input of 40 W. It dissipates 36 W by heating its surroundings. Calculate its efficiency, as a decimal and as a percentage.

⚠ Watch out

Saying energy gets 'used up' or 'lost'. It is never destroyed — it is dissipated: still there, but spread out and stored in less useful ways, usually warming the surroundings.

🧠

Memory hook

Dissipated energy is like a bag of rice spilled across the kitchen floor: every grain is still there, but good luck cooking with it. Energy in = useful out + dissipated.

✓

Check yourself

An electric motor has an efficiency of 0.25. What happens to the other 75% of the energy supplied to it — and does that energy still exist?

Flashcards

(13)
Can energy be created or destroyed?
No. It can be transferred usefully, stored or dissipated, but it is never created or destroyed.
What happens to the total energy of a closed system when energy is transferred inside it?
Nothing. No energy gets in or out, so there is no net change to the total — the energy just moves between stores.
What does 'dissipated' mean?
Spread out into the surroundings, so the energy is stored in less useful ways.
Why is dissipated energy called 'wasted' if it still exists?
Because it is no longer stored in a way we can easily use for the job we wanted done.
Is heating always a wasted transfer?
No. It depends on the device's purpose: heating the air is useful in a hairdryer but wasted in a desk fan.
How does lubrication reduce unwanted energy transfers?
It reduces friction between moving parts, so less energy is dissipated by heating the parts and their surroundings.
How does thermal insulation help keep a building warm?
It lowers the rate of energy transfer from the warm inside to the colder outside.
How does thermal conductivity affect conduction through a material?
The higher the thermal conductivity, the higher the rate of energy transfer by conduction across the material.
Which walls make a building cool most slowly?
Thick walls made of a material with a low thermal conductivity.
Give the two equations for efficiency.
efficiency = useful output energy transfer ÷ total input energy transfer, or efficiency = useful power output ÷ total power input
Your efficiency answer comes out bigger than 1. What has gone wrong?
You've divided the wrong way round. Useful goes on top: efficiency can never be more than 1 (100%).
Higher only: how can you increase the efficiency of an intended energy transfer?
Reduce the unwanted transfers — for example, lubricate moving parts or add thermal insulation — so more of the input ends up as useful output.
In the beaker-cooling investigation, how do you tell which material is the best thermal insulator?
Plot a cooling curve for each material: the best insulator is the one whose water cools most slowly.

Tap any card to flip it, or use Study as deck to go through them one at a time. In the full lesson these run as a spaced-repetition deck — you rate each card Hard, Good or Easy and the tricky ones keep coming back until they stick.

Learning with Lightbulb is opening soon

You can use this lesson now. Join the waitlist and we'll let you know when the full Lightbulb experience is ready.

Keep me posted

More AQA GCSE Physics topics

See the full AQA Physics curriculum →

How this lesson was checked. This AQA GCSE Physics (specification 8463)lesson was published through Lightbulb Learning's human-designed editorial process — the educational standards, accuracy rules and publication checks it must pass were authored and approved by Philip Halpin. It passed subject-specific assessment, automated educational checks and technical publication verification before going live (publication checks completed 8 November 2026). Published pages are monitored, human spot-checking is ongoing across the lesson library, and anything found wrong is corrected or withdrawn. How our lessons are made and checked. Spotted a mistake? Email hello@lightbulblearning.co and we'll review it.

Helpful guides for parents and students