GCSE · Physics · AQA · Spec 8463

Required practical 1: specific heat capacity

Warm 1 kg of water by 1 °C and its internal energy changes by 4200 J. But how would you ever measure that on a lab bench?

Electrical method: step by step

1Find the mass23456

Stage 1 of 6: Find the mass. paused

Find the mass · 1/6scrub the method →

Weigh the beaker with the water in it, then take away the mass of the empty beaker. What's left is the mass of the water, m. The equation wants kilograms, so 250 g is 0.25 kg.

Drag the dot along the method, or press play. Watch what each measurement is for.

The electrical set-up

Electrical method: the apparatus
Power supplyJoulemeterImmersion heaterLidThermometerWaterTop pan balanceNot to scale

Showing 1 layer: Apparatus

Explore

tap a part ↓

Tap a part to see what it does and why it is there.

Have a go: one electrical run

Problem

Illustrative numbers, not real results. A beaker holds 250 g of water, heated by an immersion heater with the lid on. The joulemeter reads 30 400 J at the start and 46 600 J at the end. The thermometer reads 20.0 °C at the start and 35.0 °C at the end. Find the specific heat capacity of the water.

Metal-block method

Put the method in order

Put the metal-block method in the order you would carry it out.

1 · First step5 · Last step
  1. Heat the metal in a hot water bath (or boiling water) for several minutes, until it is the same temperature as the water

  2. Stir gently with the thermometer and record the maximum temperature the water reaches

  3. Measure and record the dry mass of the metal on a balance

  4. Use tongs to very carefully take the hot metal from the hot water and place it in the cold water

  5. Measure out 0.1 kg of cold water into a well insulated container and record its starting temperature

Metal-block method

Your turn: find the metal's c

Illustrative numbers. A 0.30 kg metal block is heated to 100 °C, then placed in 0.1 kg of cold water at 20.0 °C. The water's highest temperature is 30.0 °C, which is also the metal's final temperature. Find the specific heat capacity of the metal.

  1. Water first: m = 0.1 kg, c = 4200 J/kg °C, and the temperature change is 30.0 − 20.0 = 10.0 °C.Water's c is the known value.
  2. missing step
Which line is step 2?

Two methods, side by side

Electrical methodvsMetal-block method

Same equation underneath. Tap a row to think about why.

Focus

Precision and kit

Electrical method

Usually less precise. More common, but needs expensive accurate joulemeters.

Metal-block method

Usually gives more precise results.

The insight

More common does not mean more precise.

How the energy is found

Electrical method

Measured directly: the joulemeter's end reading minus its start reading.

Metal-block method

Worked out from the water: energy gained by the water = m × c × Δθ for the water, and the metal lost the same amount.

What is heated

Electrical method

Water in a beaker, heated by an immersion heater. Works well for liquids and can work for some solids.

Metal-block method

A metal sample, heated to a known temperature (100 °C in boiling water), then placed in cold water.

Cutting energy losses

Electrical method

A lid on the beaker.

Metal-block method

A well insulated container such as a polystyrene cup. Polystyrene is a poor conductor (a good thermal insulator), so it reduces loss by conduction.

Checking against 4200

Electrical method

With water, tends to give a value a little higher than the actual 4200 J/kg °C.

Metal-block method

Uses water's 4200 J/kg °C as a known value to find the metal's c.

WHAT YOU'VE LEARNED

A quick recap of today's lesson.

Two experiments, one big question: how much energy does it take to warm 1 kg of a material by 1 °C?

What you need to know

  • Specific heat capacity, c, is the change in internal energy when 1 kg of a material changes temperature by 1 °C.
  • Its unit is J/kg °C, and for water the value is 4200 J/kg °C.
  • Have a goSam says, 'The unit of specific heat capacity is just J, because it's energy.' What has Sam left out?

    Per kilogram and per °C: the unit is J/kg °C.

    c is the energy change for 1 kg changing by 1 °C, so the unit has to carry the 'per kg' and the 'per °C'.

  • Two ways to find it: heat a sample electrically with an immersion heater, or heat a metal block and place it in water.
  • Electrical method: a joulemeter sits between the power supply and the heater, so it measures the energy supplied directly.
  • The power supply is low voltage to reduce the risk of electrocution. The lid reduces energy losses to the surroundings.
  • Temperature change is end minus start, and c = ΔE ÷ (m × Δθ).
  • Have a goA joulemeter shows 3000 J of energy supplied to a 0.5 kg sample, which warms by 4 °C. What is c?

    1500 J/kg °C

    c = 3000 ÷ (0.5 × 4) = 3000 ÷ 2. Dividing by the mass alone gives 6000, which forgets the temperature change.

  • Do it three times, add the three values and divide by three for a mean. That gives a better answer.
  • The electrical method tends to give a value a little higher than water's actual 4200 J/kg °C.
  • Metal-block method: by conservation of energy, the energy gained by the water equals the energy lost by the metal.
  • Have a goA hot metal block goes into cold water. Where does the energy the water gains come from?

    From the metal.

    Energy is conserved, so the water gains exactly what the metal loses. It doesn't appear from nowhere.

  • A polystyrene cup is a poor conductor, so it reduces energy loss by conduction. The metal-block method is usually more precise.

The big picture

Specific heat capacity, c, is the change in internal energy when 1 kg of a material changes temperature by 1 °C, in J/kg °C; for water it is 4200. You can measure it two ways: heat a sample electrically with an immersion heater and a joulemeter, or heat a metal block and place it in insulated water. Either way you use c = ΔE ÷ (m × Δθ), and you repeat the experiment and take a mean.

Key points

1Specific heat capacity c is the change in internal energy when 1 kg of a material changes temperature by 1 °C; the unit is J/kg °C and water's value is 4200 J/kg °C.
2Both methods use c = ΔE ÷ (m × Δθ). The electrical method measures the energy supplied with a joulemeter; the metal-block method uses energy gained by the water = energy lost by the metal.
3A lid or a polystyrene cup reduces energy lost to the surroundings, and repeating three times to find a mean gives a better answer.
4The electrical method tends to give a value a little higher than 4200 J/kg °C for water; the metal-block method is usually more precise.

Worked example

Problem

Illustrative numbers. Three runs of the electrical method give c = 4310, 4260 and 4330 J/kg °C. Find the mean, then say how it compares with water's actual value.

⚠ Watch out

Treating the measured number as the final truth. Energy can be lost to the surroundings, hence the lid and cup. The electrical method tends to give a value a little higher than 4200 J/kg °C for water. For the metal's c, use the metal's own mass and temperature change.

🧠

Memory hook

Energy per kilogram per degree: ΔE ÷ (m × Δθ). Keep the heat in with a lid or a polystyrene cup.

✓

Check yourself

Without looking back: a classmate gets 4350 J/kg °C for water with the electrical method. Is that a surprise, and how would they get a better answer?

Flashcards

(14)
What is specific heat capacity?
The change in internal energy when 1 kg of a material changes temperature by 1 °C. Unit: J/kg °C.
What value of c do you use for water?
4200 J/kg °C.
What are the two methods for finding c?
Electrical heating with an immersion heater, or heating a metal block and placing it in water.
What apparatus does the electrical method use?
Water in a beaker, an immersion heater, a low voltage power supply, a joulemeter between the supply and the heater, a thermometer, a top pan balance and a lid.
Why is a low voltage power supply used?
To reduce the risk of electrocution.
How do you find the mass of the water and the energy supplied?
Mass: beaker with water minus empty beaker. Energy: the joulemeter's end reading minus its start reading.
Why does the electrical method use a lid?
To reduce energy losses to the surroundings.
Why do the experiment three times?
To find a mean value (add the three values, divide by three) and get a better answer.
Is the electrical method more likely to give a c for water that is too high or too low?
A little bit too high: it tends to give a value above the actual 4200 J/kg °C.
What is the principle behind the metal-block method?
Conservation of energy: the energy gained by the water equals the energy lost by the metal.
How is the metal heated for the metal-block method?
In a hot water bath, or in boiling water (100 °C), for several minutes until it is at the same temperature as the water: thermal equilibrium.
How do you move the hot metal into the cold water?
With a pair of tongs, very carefully.
Why is the cold water in a polystyrene cup?
Polystyrene is a poor conductor (a good thermal insulator), so it reduces energy loss to the surroundings by conduction.
Which method is usually more precise, and what does the other one need?
The metal-block method is usually more precise. The electrical method is more common but needs expensive accurate joulemeters.

Tap any card to flip it, or use Study as deck to go through them one at a time. In the full lesson these run as a spaced-repetition deck — you rate each card Hard, Good or Easy and the tricky ones keep coming back until they stick.

Learning with Lightbulb is opening soon

You can use this lesson now. Join the waitlist and we'll let you know when the full Lightbulb experience is ready.

Keep me posted

More AQA GCSE Physics topics

See the full AQA Physics curriculum →

How this lesson was checked. This AQA GCSE Physics (specification 8463)lesson was published through Lightbulb Learning's human-designed editorial process — the educational standards, accuracy rules and publication checks it must pass were authored and approved by Philip Halpin. It passed subject-specific assessment, automated educational checks and technical publication verification before going live (publication checks completed 13 November 2026). Published pages are monitored, human spot-checking is ongoing across the lesson library, and anything found wrong is corrected or withdrawn. How our lessons are made and checked. Spotted a mistake? Email hello@lightbulblearning.co and we'll review it.

Helpful guides for parents and students