GCSE · Physics · AQA · Spec 8463

Ohmic conductors and resistors with changing resistance

Draw one straight line and you have a ruler for every other component. The ones that bend away from it are telling you their resistance is changing.

Meet the ruler: an ohmic resistor

-12-60612-6-3036p.d. across the resistor (V)Current (A)3.00 ACurrent at 6 Vdrag me up or down
Resistor value 2 Ω

Resistor value: 2 Ω. Current at 6 V: 3.00 A

This resistor sits at a steady temperature. Slide the resistor value (or drag the dot) and watch the line. Each time, read the current at 6 V, then work out 6 ÷ I. Notice what the answer is.

Watch out: These are practice numbers for an ohmic resistor kept at a constant temperature, not readings from a real one.

Inside the filament

?

Reason it through

Why does a filament lamp's resistance go up as it heats up?

Link 1 of 4

First link · your turn

Start with the metal itself. What is a metal made of?

2
Locked — reveal the link above first
3
Locked — reveal the link above first
4
Locked — reveal the link above first

Predict, then check: the diode

A diode is a component whose resistance depends on the direction and size of the p.d. Commit to an answer before you reveal.

You sweep the p.d. across a diode from negative, through zero, to positive. Which description of the current fits?

Physics · Fuses

Which fuse would you trust?

An appliance normally takes 11 A. A fuse is a thin wire that melts if the current is too high, which breaks the circuit and limits the current to the device.

Which of these is closest to what you think?
How sure are you?

Physics · Components

What changes its resistance?

For each component, what (if anything) changes its resistance?

Still to sort

Nothing, at constant temperature (0)

Resistance stays the same.

Heating it raises its resistance (0)

Hotter means higher resistance.

Where the line is: Same direction as a metal wire: hotter metal, higher resistance.

Heating it lowers its resistance (0)

Hotter means lower resistance.

Where the line is: The opposite way round from a metal wire or filament.

Brighter light lowers its resistance (0)

Light level is the trigger.

The direction and size of the p.d. (0)

Which way round, and how big.

6 of 6 still to sort.

Pick a component, then the box it belongs in.

UK note

This topic is AQA GCSE Physics (8463), specification section 4.2.1.

An LDR as a light sensor

+6 V0 VFixed resistor10 kΩ10 kΩ · 1.2 VLDR40 kΩ · 4.8 VV4.8 Vp.d. across theLDR1Light level (1dark, 4 verybright)slide tochange thelight

Light level (1 dark, 4 very bright): 1. p.d. across the LDR: 4.8 V

The bigger resistance takes the bigger share of the 6 V. A thermistor works the same way for heating, using temperature instead of light. All the resistances here are practice values.

A fixed resistor and an LDR share a 6 V supply. Change the light level and watch the LDR's p.d. Suppose a switch turns the streetlight on when the p.d. across the LDR is more than 3.5 V (a practice figure). At which light levels does the light come on?

WHAT YOU'VE LEARNED

A quick recap of today's lesson.

What you need to know

  • Find resistance with R = V ÷ I: V in volts, I in amps, R in ohms. Convert milliamps to amps first.
  • Have a goA meter shows 50 mA through a component. Before you divide the p.d. by it, what do you have to do to the 50 mA?

    Convert it to amps: 50 mA is 0.050 A.

    R = V ÷ I only gives a resistance in ohms when the current is in amps, so milliamps must be converted first.

  • An ohmic resistor has constant resistance if its temperature stays the same. Its I–V line is straight through the origin, whichever way round the p.d. is applied.
  • So current is directly proportional to p.d. More resistance means less current at any p.d., and a less steep line.
  • Have a goYou swap an ohmic resistor for one with a bigger resistance and keep the p.d. the same. Does the current go up, go down or stay the same?

    It goes down.

    The same p.d. divided into a bigger resistance leaves a smaller current, which is why the I–V line is less steep.

  • A filament lamp is not ohmic. Its resistance rises as the p.d. rises, because the filament gets hotter and brighter. Its graph is a curve, symmetrical for positive and negative p.d.
  • Have a goYour mate looks at a curved lamp graph and says: 'That lamp is broken, a proper one would give a straight line.' Fair?

    No. A curve is exactly what a working filament lamp gives.

    A filament lamp is not ohmic: its resistance rises as it heats, so its graph is a curve and a straight line would be the odd result.

  • In a metal, resistance comes from collisions between free electrons and metal ions. Hotter ions vibrate harder, so collisions become more frequent.
  • A diode's resistance depends on direction. Reverse bias: very high resistance, almost no current. Forward bias: significant current only above a threshold p.d.
  • A fuse's thin wire melts if the current is too high. Choose the lowest rating above the normal current, such as 13 A for 11 A.
  • An LDR's resistance falls as light gets brighter. A thermistor's resistance falls as it gets hotter. Both are semiconductors.
  • Put an LDR or thermistor in a potential divider and its changing resistance changes its share of the supply p.d., which can trigger a switch.

The big picture

Resistance is found from a pair of readings using R = V ÷ I. An ohmic resistor has constant resistance at constant temperature, so its I–V graph is a straight line through the origin. Other components bend away from that line because their resistance changes: a filament lamp's and a fuse wire's rise as they heat up, a thermistor's falls as it heats, an LDR's falls in brighter light, and a diode depends on the direction and size of the p.d. A thermistor or LDR in a potential divider makes a sensor.

Key points

1R = V ÷ I gives resistance from a pair of readings. Use volts, amps and ohms, and turn milliamps into amps.
2A straight I–V line through the origin means an ohmic resistor, with constant resistance while the temperature stays the same.
3A less steep line on an ohmic resistor's graph means a higher resistance.
4A filament lamp's resistance rises as it heats, so its I–V graph is a curve and it is not ohmic.
5A diode is not ohmic: very high resistance in reverse, and current only above a threshold p.d. in forward.
6An LDR's resistance falls in brighter light and a thermistor's falls as it heats, and either can be a sensor in a potential divider.

Worked example

Problem

A pupil tests a filament lamp. With 2.0 V across it the current is 0.40 A. With 6.0 V across it the current is 0.75 A. These are practice numbers. Work out the lamp's resistance at each p.d. and say what the answers show.

⚠ Watch out

Assuming every component has one fixed resistance. Only an ohmic resistor at constant temperature does. A filament lamp's resistance rises as it heats, a thermistor's falls as it heats, an LDR's falls in brighter light, and a diode depends on the direction of the p.d.

🧠

Memory hook

Straight means steady. A bend means something is changing: heat, light, or which way round the p.d. goes.

✓

Check yourself

A friend says: 'Double the p.d. across any component and the current doubles.' For which kind of component is that true, and what would a filament lamp do instead?

Flashcards

(10)
Which equation gives resistance, and in what units?
R = V ÷ I, with R in ohms, V (p.d.) in volts and I (current) in amps.
What is an ohmic resistor?
A component with constant resistance, as long as its temperature stays the same.
What is the I–V graph of an ohmic resistor like?
A straight line through the origin, so current is directly proportional to p.d. It is the same whichever way round the p.d. is applied.
Why is a filament lamp not an ohmic conductor?
Its resistance increases as the p.d. rises, because the filament gets hotter and brighter. Its I–V graph is a curve.
What causes resistance in a metal?
Collisions between the free electrons and the metal ions. More vigorous vibration of the ions means more frequent collisions.
How does a diode's resistance behave?
It depends on the direction and size of the p.d. In reverse bias it is very high, so almost no current flows. In forward bias current flows significantly only above a threshold p.d.
What does a fuse do, and how do you choose one?
Its thin wire melts if the current is too high, breaking the circuit. Choose the lowest rating above the normal current.
How does an LDR's resistance change?
It decreases as the brightness of the light on it increases.
How does a thermistor differ from a metal wire when heated?
A thermistor's resistance decreases as its temperature increases. A metal wire's or filament's resistance increases.
How does an LDR or thermistor work as a sensor in a potential divider?
The supply p.d. is shared in the ratio of the resistances, so when the sensor's resistance changes, the p.d. across it changes and can trigger a switch.

Tap any card to flip it, or use Study as deck to go through them one at a time. In the full lesson these run as a spaced-repetition deck — you rate each card Hard, Good or Easy and the tricky ones keep coming back until they stick.

Learning with Lightbulb is opening soon

You can use this lesson now. Join the waitlist and we'll let you know when the full Lightbulb experience is ready.

Keep me posted

More AQA GCSE Physics topics

See the full AQA Physics curriculum →

How this lesson was checked. This AQA GCSE Physics (specification 8463)lesson was published through Lightbulb Learning's human-designed editorial process — the educational standards, accuracy rules and publication checks it must pass were authored and approved by Philip Halpin. It passed subject-specific assessment, automated educational checks and technical publication verification before going live (publication checks completed 5 November 2026). Published pages are monitored, human spot-checking is ongoing across the lesson library, and anything found wrong is corrected or withdrawn. How our lessons are made and checked. Spotted a mistake? Email hello@lightbulblearning.co and we'll review it.

Helpful guides for parents and students