GCSE · Physics · AQA · Spec 8463
Required practical 4: I–V characteristics
Run one test on a resistor, a filament lamp and a diode and you get three completely different graphs. Learn the method, then read the shapes.
Same test, three components, three graphs
Predict first: which one lets almost no current through when the p.d. is reversed? Then slide from 1 to 3: 1 is the ohmic resistor, 2 is the filament lamp, 3 is the diode. These are sketches of the shapes on a relative scale, not measured readings.
The method, step by step
Step through it in order. Each step has a reason.
- Repeat and averageTake repeat readings and average them to get more accurate results.
- Plot and drawPlot current against p.d. and draw a best fit line through the points, straight or curved, to show the trend.
This is required practical 4, I–V characteristics, in AQA GCSE Physics (8463, section 4.2.1).
Why the lamp's graph curves
Reason it through
Why does the filament lamp's resistance rise as the p.d. across it goes up?
First link · your turn
You turn up the p.d. across the lamp. What happens to the current through it?
Equations you need
Taken directly from the exam-board specification.
R = resistance (ohm (Ω)) · V = potential difference (volt (V)) · I = current (ampere (A))
WHAT YOU'VE LEARNED
A quick recap of today's lesson.
What you need to know
- Wire the lamp to a DC supply, with a variable resistor and ammeter in series and a voltmeter in parallel across it.
Have a goSam says: 'It's one loop, so both meters go in series with the lamp.' Is Sam right about the voltmeter?
No. The voltmeter goes in parallel, across the lamp.
The voltmeter reads the p.d. across the lamp, so it connects across it. Only the ammeter sits in series.
- The variable resistor changes the p.d. across the lamp, and so its brightness. The ammeter and voltmeter give you each pair of readings.
- Start with a quick check at different variable resistor settings, so you can choose the most accurate ammeter and voltmeter.
- Cover 0 V, the lamp's maximum p.d. and at least four other readings. Take many more if you can.
- Take repeat readings and average them. Reverse the supply connections too, to record negative readings and compare the two directions.
- Plot current against p.d. and draw a best fit line, straight or curved. Points off the line may be errors to check.
- To find resistance, use R = V ÷ I, or read the current at a chosen p.d. from the best fit line.
- An ohmic resistor gives a straight line through the origin: current is directly proportional to p.d. and resistance is constant, while temperature stays the same.
Have a goA resistor stays at the same temperature and you double the p.d. across it. What happens to the current?
It doubles.
A straight line through the origin means current is directly proportional to p.d. Halving or staying the same would not give that line.
- A filament lamp gives a curve, with the same shape when reversed. Its resistance rises as the filament gets brighter and hotter.
Have a goPredict: you turn the lamp from half brightness up to full brightness. Does its resistance go up, go down or stay the same?
It goes up.
Its resistance rises as the filament gets brighter and hotter. Staying the same is how an ohmic resistor behaves, not a lamp.
- A diode lets current flow one way only: none below the threshold p.d. forwards, then a rapid rise, and almost none reversed.
The big picture
In this required practical you connect a component to a DC supply with a variable resistor and an ammeter in series and a voltmeter in parallel, change the p.d. and record pairs of current and p.d. readings. You plot current against p.d. and draw a best fit line. An ohmic resistor gives a straight line through the origin, a filament lamp gives a curve because its resistance rises as it heats, and a diode lets current through one way only.
Key points
Worked example
Problem
A pupil tests an ohmic resistor at constant temperature. The best fit line passes through the origin. Reading from the line, the current is 0.50 A at 2.0 V and 1.00 A at 4.0 V. Work out the resistance at each p.d. and say what the answers show.
⚠ Watch out
Dividing the wrong way round. Resistance is p.d. ÷ current, R = V ÷ I, so put the p.d. on top. Current ÷ p.d. gives a number that is not a resistance.
Memory hook
Resistor: straight and steady. Lamp: bends as it heats. Diode: a one-way street with a threshold.
Check yourself
An unknown component's graph is a straight line through the origin. What does that tell you about its resistance, and what must stay the same?
Flashcards
(13)In the I–V circuit, how is each meter connected?
What does changing the variable resistor do in this circuit?
What range of p.d. values should you cover?
Why take many more readings than the minimum?
How do you choose the most accurate ammeter and voltmeter?
How do you make readings more accurate, and how do you test the other direction?
What could a plotted point far off the best fit line mean?
What does an ohmic resistor's I–V graph look like, and what does it show?
What does a filament lamp's I–V graph look like?
Why does a lamp's resistance rise as the current rises?
What is special about a diode's I–V graph?
What changes in the investigation when the component is a diode?
Which components behave the same whichever way round the p.d. is applied?
Tap any card to flip it, or use Study as deck to go through them one at a time. In the full lesson these run as a spaced-repetition deck — you rate each card Hard, Good or Easy and the tricky ones keep coming back until they stick.
Learning with Lightbulb is opening soon
You can use this lesson now. Join the waitlist and we'll let you know when the full Lightbulb experience is ready.
Keep me postedMore AQA GCSE Physics topics
- Current, resistance and potential difference (V = I R)
- Diodes
- Direct and alternating potential difference
- Electric fields (physics only)
- Electrical power (P = V I and P = I^2 R)
- Energy transfers in everyday appliances (E = P t and E = Q V)
- Ohmic conductors and resistors with changing resistance
- Series and parallel circuits
- Static electricity and charging by friction (physics only)
- The National Grid
- Thermistors and LDRs
How this lesson was checked. This AQA GCSE Physics (specification 8463)lesson was published through Lightbulb Learning's human-designed editorial process — the educational standards, accuracy rules and publication checks it must pass were authored and approved by Philip Halpin. It passed subject-specific assessment, automated educational checks and technical publication verification before going live (publication checks completed 4 November 2026). Published pages are monitored, human spot-checking is ongoing across the lesson library, and anything found wrong is corrected or withdrawn. How our lessons are made and checked. Spotted a mistake? Email hello@lightbulblearning.co and we'll review it.